Question: The intake and impeller of my jetski are dirty. How to clean them?

  EJU01119  Cleaning the jet intake and  impeller

If weeds or debris get caught in the intake or impeller, cavitation can occur, causing jet thrust to decrease even though engine speed rises. If this condition is allowed to continue, the engine will overheat and may seize. If there is any sign that the jet intake or impeller is clogged with weeds or debris, beach the watercraft and check the intake and impeller. Always stop the engine before beaching the watercraft.
<PIC>

  WARNING
Before attempting to remove weeds or debris from the jet intake or impeller areas, shut the engine off and remove the clip from the engine shut-off switch. Severe injury or death could result from contact with the rotating parts of the jet pump.

1. Turn the watercraft on its side as shown.
  CAUTION:
@   Place a suitable clean cloth or carpetG ing underneath the watercraft to pro- tect it from abrasions and scratches.  G  Always turn the watercraft over onto its port (left) side.  G  When turning the watercraft on its side, support the bow so the handlebars cannot be bent or damaged.
<PIC>

2. Remove any weeds or debris from around the drive shaft, impeller, pump housing, and jet thrust nozzle.  If debris is difficult to remove, consult your Yamaha dealer.
  CAUTION:
Always avoid operating your watercraft in areas where weed growth is thick. If traveling in weeded areas is unavoidable, operate the engine alternately at partial throttle and full throttle. Weeds tend to accumulate more at a steady speed and at trolling speed. If weeds clog the intake or impeller area and cause cavitation, follow the cleaning procedure above.


Question: How to start my jetski in different situations?

  EJU01837 Starting the watercraft

  WARNING
@   Scan constantly for people, objects, G and other watercraft. Be alert for conditions that limit your visibility or block your vision of others.
<PIC>

G  Operate defensively at safe speeds and keep a safe distance away from people, objects, and other watercraft.  G  Do not follow directly behind watercraft or other boats. Do not go near others to spray or splash them with water. Avoid sharp turns or other maneuvers that make it hard for others to avoid you or understand where you are going. Avoid areas with submerged objects or shallow water.  G  Take early action to avoid collisions. Remember watercraft and other boats do not have brakes. Do not release the throttle when trying to steer away from objects—you need throttle to steer.  G  Practice reboarding in shallow water before riding in deep water.

EJU01073
  Starting and boarding in shallow water

1. Do not start the engine in less than  $60\,\mathsf{c m}$   (2 ft) of water. Put the watercraft in water that is deep enough, and then board the watercraft from the side or the rear.
<PIC>

 2. Attach the engine shut-off cord to your left wrist, and then install the clip to the engine shut-off switch.

 3. Grip the handlebars with both hands, place both feet on the floor of the footwell, start the engine, and start off.

  Starting from a dock
1. Board the watercraft from the side.
 2. Attach the engine shut-off cord to your left wrist, and then install the clip to the engine shut-off switch.
 3. Push the watercraft away from the dock, grip the handlebars with both hands, place both feet on the floor of the footwell, start the engine, and start off.
<PIC>


Question: What are basic steps to board my jetski with a passenger in deep water?

  EJU01077  Boarding with a passenger

  WARNING

Severe internal injuries can occur if water is forced into body cavities as a result of being near the jet thrust nozzle. Do not apply throttle until the passenger is seated with his or her feet on the floor of the footwell and is holding on to the operator.

1. Climb on board as noted in the previous section, and sit astride the seat. Attach the engine shut-off cord to your wrist, and then install the clip to the engine shut-off switch.
 2. Have the passenger move to the rear of the watercraft.
 3. Have the passenger get on board and sit on the seat.
<PIC>

  NOTE:

When a passenger is getting on board, both the passenger and the operator should try to balance the watercraft.

4. The operator should check to see that the passenger has his or her feet on the floor of the footwell and that he or she is securely holding on to the operator.
 5. Start the engine, look in all directions, and then accelerate to planing speed.
<PIC>

  WARNING

Before starting off, make sure that there are no boats, obstructions, or swimmers around you.
<PIC>


Question: If it is difficult to balance the jetski at a stand still, what should I do?

  NOTE:

The heavier the total weight of the operator and passengers, the more difficult it will be to balance the watercraft. Do not operate the watercraft when the total weight exceeds  $160\,{\sf k g}$   (353 lb) including any cargo. If it is difficult to balance the watercraft at a standstill, proceed as follows:

1. The passenger must steady the watercraft while the operator is boarding. The operator pulls himself up onto the platform into a seating position, then balances the watercraft.
<PIC>

 2. Attach the lanyard to your left wrist, then install the clip on the lanyard to the engine shut-off switch. Start the engine and keep it at idle.
 3. The passenger pulls himself up on the platform, kneels down, then crawls onto the seat as the watercraft accelerates.
<PIC>

 4. The watercraft can now be accelerated to planing speed, then the operator can reduce the throttle to the desired running speed.
<PIC>


Question: What is the max load of the jetski?

Maximum load: 160 kg (353 lb)  Load is the total weight of cargo,  operator and passenger.


Question: What is and is not usually covered in the warranty policy for a function keyboard?

WHAT IS AND IS NOT COVERED

Please note that our warranty is not an unconditional guarantee. If the  product, in reasonable opinion, malfunctions within the warranty  period, we will provide you at its sole discretion with a repaired or  replacement product, either new or refurbished, with a similar function  that is equal or greater in value depending on supply.

Our warranty does not cover the following:

any product or serial number/warranty sticker modification applied  without permission;
any damage that is not a manufacturing defect;

damage, deterioration or malfunction resulting from: accident,  abuse, misuse, neglect, fire, water, lightning, or other acts of nature,  unauthorized product modification or failure to follow instructions  included with the product;
 improper installation, unauthorized alterations or modifications, or repair  or attempted repair by anyone not authorized;
shipping or transport damage (claims must be made with the carrier);
normal wear and tear.

We do not warrant that this product will meet your requirements. It  is your responsibility to determine the suitability of this product for your  purpose. For Store orders, we cover two way return shipping for all  exchanges and returns. For all other authorized dealers, Support  does not cover return shipping and only covers one way shipping back to the end user for exchanges. Two way expedited shipping  is provided for all PSUs covered under the Less Than Three program,  indiscriminate of purchase location, provided the location is an approved reseller.


Question: What is usually the exclusion of damages or disclaimer in the warranty policy of a function keyboard?

 IV. EXCLUSION OF DAMAGES (DISCLAIMER)

Our sole obligation and liability under this warranty is limited to  the repair or replacement of a defective product with either a new or  refurbished product with a similar function that is equal or greater in value  at our option. We shall not, in any event, be liable for any incidental or  consequential damage, including but not limited to damages resulting  from interruption of service and loss of data, business, or for liability in  tort relating to this product or resulting from its use or possession.


Question: How can you set up a function keyboard?

a. Connect the USB-C Cable to the port on the rear of the keyboard, and the other end to any
available USB 2.0 (or faster) port on your PC.
b. Attach the wrist rest (Full Size and Tenkeyless only) to the front of the keyboard. The wrist
rest is magnetic—it will connect and center itself automatically.
c. Deploy the angled rear feet on the bottom of the keyboard if you want a greater amount of
typing angle. There are two nested feet for medium or high degrees of typing angle.


Question: How can you remove or reinstall keyswitches of a function keyboard?

Using the included keyswitch removal tool, grip the keyswitch from  the top, orienting the ends of the tool along the back and front  of the keyswitch. There are two tabs that retain the keyswitch  into the plate, and when depressed, allow removal. Note that the  tool should not scrape the top plate, and it is unnecessary to grip  underneath the switch. Grip the sides of the plastic housing only,  near the bottom.
<PIC>
In order to reinstall key switches into the keyboard first make  sure that all of the pins are straight and not kinked or folded  against the bottom housing of the switch. Visually check that  the two metal prongs on the keyswitch correspond with the two  sockets on the keyswitch socket on the keyboard. Insert the  switch into the keyboard socket firmly using direct overhead  pressure. The sides of the switch housing should be against the  top plate of the keyboard when inserted correctly.
<PIC>


Question: How can you use a function keyboard with cam software?

A. DOWNLOADING AND INSTALLING CAM SOFTWARE
Go for the latest version of CAM
B. SETUP OF CAM PROFILES AND STORING ON THE KEYBOARD
The Function Keyboard has four onboard profiles that can be setup and stored
via CAM software. After profile information is stored, it is not necessary to run
CAM to operate stored lighting, macros, etc.
C. CONTROLLING PROFILE SWITCHING
Depressing the FN (short for “Function”) key + one of the F1, F2, F3, or F4
keys will change to the profile stored at that number value (1 through 4,
respectively).
D. LIGHTING MODES
There are four default lighting modes stored on profiles #1 through #4 and
can be accessed by depressing the FN key + F1, F2, F3, or F4.
E. CUSTOMIZING RGB LIGHTING
By using CAM/Keyboard/Lighting, users are able to customize lighting per key,
and set up lighting under profiles (if desired), as described in SECTION B.
F. CUSTOMIZING KEYBOARD MACROS
By using CAM/Keyboard/Macros, users are able to create both simple and
complex macros, and store them under profiles (if desired), as described in
SECTION B.
G. REBINDING KEYS
By using CAM/Keyboard/Key Remapping, users are able to create new and
customized key bindings, and store them under profiles (if desired), as described
in SECTION B.


Question: How can you use a function keyboard in hardware mode?

A. CONTROLLING RGB LIGHTING
There are four default lighting modes stored on profiles #1 through #4 and can be
accessed by depressing the FN key + F1, F2, F3, or F4. If customized lighting has
been set up, and assigned custom lighting to one of the onboard profiles, custom
lighting will activate when switching to a custom profile.
B. SWITCHING TO STORED PROFILES (1-4)
Depressing the FN (short for “Function”) key + one of the F1, F2, F3, or F4 keys will
change to the profile stored at that number value (1 through 4, respectively).


Question: What is the overview of the base station of a landline?

Press to find handsets.
 Press and hold to enter the registration  mode.
<PIC>
Press to find handsets.
Press and hold to enter the registration  mode.
<PIC>
Speaker


Question: How can you connect the base station of a landline?

Warning
Risk of product damage! Ensure that the power supply  voltage corresponds to the voltage printed on the back  or the underside of the phone.
  Use only the supplied power adapter to charge the  batteries.
<PIC>
 Note
If you subscribe to the digital subscriber line (DSL) high  speed internet service through your telephone line,  ensure you install a DSL filter between the telephone  line cord and the power socket. The filter prevents  noise and caller ID problems caused by the DSL  interference. For more information on the DSL filters,  contact your DSL service provider.
The type plate is located on the bottom of the base  station.
Connect each end of the power adapter  to:
the DC input jack at the bottom of the  base station;  the power socket on the wall.
<PIC>
2   Connect each end of the line cord to:  the telephone socket at the bottom of  the base station; the telephone socket on the wall.
 the power socket on the wall.


Question: How can you  install the handset of a landline?

The batteries are pre-installed in the handset.  Pull the battery tape off from the battery door  before charging.
<PIC>
 Caution
<PIC>
 Risk of explosion! Keep batteries away from heat,  sunshine or fire. Never discard batteries in fire.
 Use only the supplied batteries.
  Risk of decreased battery life! Never mix different  brands or types of batteries.
<PIC>
 Charge the batteries for 8 hours before first use.
If the handset becomes warm when the batteries are  charging, it is normal.
 Warning
 Check the battery polarity when inserting in the  battery compartment. Incorrect polarity may damage  the product.


Question: How can you check the battery level  of a landline?

The battery icon displays the current battery
<PIC>
The handset turns off if the batteries are empty.  If you are on the phone, you hear warning  tones when the batteries are almost empty. The  call gets disconnected after the warning.
<PIC>


Question: What can you do if your landline is in searching status?

My handset is in searching status, what do I  do?

 Make sure that the base station has power  supply.

Register the handset to the base station.

Move the handset closer to the base  station.


Question: How can you know about the current status  with different LED indicator behavior on a landline?

The table below shows you the current status  with different LED indicator behavior on the  handset.
<PIC>


Question: How can you know about  the current status  with different LED indicator behavior on the  base station of a landline?

The table below shows you the current status  with different LED indicator behavior on the  base station.
<PIC>


Question: How can you lower the roll bar of a lawn mower?

 Lowering the Roll Bar
Important:  Lower the roll bar only when absolutely necessary.
1. Remove the hairpin cotters and remove the 2 pins ( Figure 9 ). 2. Lower the roll bar to the down position ( Figure 8 ). Note:  There are 2 down positions; refer to Figure 8 .
<PIC>
Figure 8
3. Install the 2 pins and secure them with the hairpin cotters ( Figure 9 ).
<PIC>
1. Roll bar 3. Pin 2. Raised position 4. Hairpin cotter


Question: How can you adjust the rear-shock assemblies   for a lawn mower with suspension system only?

Adjusting the Rear-Shock Assemblies
Machines with Suspension System Only
The suspension system adjusts to provide a smooth and comfortable ride. You can adjust the rear 2-shock assemblies to quickly and easily change the suspension system. Position the suspension system where you are most comfortable.
The slots for the rear-shock assemblies have detent positions for reference. You can position the rear-shock assemblies anywhere in the slot, not just in the detent positions. The following graphic shows the position for a soft or firm ride and the different detent positions ( Figure 13 ).
<PIC>
1. Firmest position 3. Detents in the slots 2. Softest position
Note:  Ensure that the left and right rear-shock assemblies are always adjusted to the same positions.
Adjust the rear-shock assemblies ( Figure 14 ).
<PIC>


Question: How can you adjust the height of cut for a lawn mower with an electric deck lift?

 Adjusting the Height of Cut For Machines with an Electric Deck Lift
1. Push up on the deck-lift switch ( Figure 31 ).
<PIC>
Figure 31
1. Push up to raise the deck. 2. Push down to lower the deck.
2. Select a hole in the height-of-cut bracket corresponding to the height of cut desired, and insert the pin ( Figure 32 ).
<PIC>
Figure 32
1. Height-of-cut pin 2. Height-of-cut bracket


Question: How can you load a lawn mower?

Loading the Machine
WARNING
Loading a machine onto a trailer or truck increases the possibility of tip-over and could cause serious injury or death.
 Use extreme caution when operating a machine on a ramp.
 Back the machine up the ramp and drive it forward down the ramp.
Avoid sudden acceleration or deceleration while driving the machine on a ramp as this could cause a loss of control or a tip-over situation.
1. If using a trailer, connect it to the towing vehicle and connect the safety chains.
2. If applicable, connect the trailer brakes and lights.
3. Lower the ramp, ensuring that the angle between the ramp and the ground does not exceed 15 degrees ( Figure 39 ).
<PIC>
Figure 39
1. Full-width ramp in stowed 4. Ramp is at least 4 times position as long as the height of the trailer or truck bed to the ground 2. Side view of full-width 5.  $\mathsf{H}\!\!=$  height of the trailer or ramp in loading position truck bed to the ground 3. Not greater than 6. Trailer 15 degrees
4. Back the machine up the ramp ( Figure 40 ).
<PIC>
1. Back the machine up the 2. Drive the machine forward ramp. down the ramp.
5. Shut off the engine, remove the key, and engage the parking brake.
6. Tie down the machine near the front caster wheels and the rear bumper with straps, chains, cable, or ropes ( Figure 41 ). Refer to local regulations for tie-down requirements.
<PIC>
Figure 41
1. Tie-down loops


Question: How can you unload a lawn mower?

Unloading the Machine
1. Lower the ramp, ensuring that the angle between the ramp and the ground does not exceed 15 degrees ( Figure 39 ).
<PIC>
Figure 39
1. Full-width ramp in stowed 4. Ramp is at least 4 times position as long as the height of the trailer or truck bed to the ground 2. Side view of full-width 5.  $\mathsf{H}\!\!=$  height of the trailer or ramp in loading position truck bed to the ground 3. Not greater than 6. Trailer 15 degrees
2. Drive the machine forward down the ramp ( Figure 40 ).
<PIC>
1. Back the machine up the 2. Drive the machine forward ramp. down the ramp.


Question: How can you change the engine oil of a lawn mower?

Changing the Engine Oil
Note:  Dispose of the used oil at a recycling center.
1. Start the engine and let it run for 5 minutes. Note:  This warms the oil so that it drains better. 2. Park the machine so that the drain side is slightly lower than the opposite side to ensure that the oil drains completely. 3. Disengage the blade-control switch (PTO) and engage the parking brake.
4. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
5. Drain the oil from the engine ( Figure 49 ).
<PIC>
6. Slowly pour approximately  $80\%$   of the specified oil into the filler tube and slowly add the additional oil to bring it to the Full mark ( Figure 50 ).
<PIC>
Figure 50
7. Start the engine and drive to a flat area.
8. Check the oil level again.


Question: How can you remove the filters of a lawn mower?

Removing the Filters
1. Park the machine on a level surface, disengage the blade-control switch (PTO), and engage the parking brake.
 2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
 3. Release the latches on the air cleaner and pull the air-inlet cover off the air-cleaner body ( Figure 56 ).
 4. Clean the air-inlet screen and cover.
 5. Install the air-inlet cover and secure it with the latches ( Figure 56 ).
<PIC>
1. Air-inlet cover 3. Air-cleaner body
 2. Air-inlet screen 4. Latch
6. Release the latches on the air cleaner and pull the air-cleaner cover off the air-cleaner body ( Figure 57 ).
 7. Clean the inside of the air-cleaner cover with compressed air.
 8. Gently slide the primary filter out of the air-cleaner body ( Figure 57 ). Note:  Avoid knocking the filter into the side of the body.
<PIC>
Figure 57
1. Inner filter 4. Latch 2. Primary filter 5. Air-cleaner body 3. Air-cleaner cover
 9. Remove the inner filter only if you intend to replace it. Important:  Never attempt to clean the inner filter. If the safety filter is dirty, then the primary filter is damaged. Replace both filters. the inner air filter.


Question: How can you replace the mower belt of a lawn mower?

 Replacing the Mower Belt
1. Park the machine on a level surface, disengage the blade-control switch (PTO), and engage the parking brake. 2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Lower the mower to the 3 inches height of cut.
4. Remove the belt covers ( Figure 73 ).
<PIC>
Figure 73
5. Use a   $3/8$  -inch ratchet in the square hole in the idler arm to remove tension on the idler spring ( Figure 74 ). 6. Remove the belt from the mower-deck pulleys and the clutch pulley. 7. Remove the belt guide on the spring-loaded idler arm ( Figure 74 ). 8. Remove the existing belt. 9. Install the new belt around the mower pulleys and the clutch pulley under the engine ( Figure 74 ).
<PIC>
Figure 74
1. Spring 4. Spring-loaded idler assembly
 2. Clutch pulley 5. Ratchet
 3. Mower belt 6. Square hole in the idler arm for the ratchet
10. Install the belt guide on the idler arm ( Figure 74 ).
11. Using the -inch ratchet in the square hole, install the idler spring ( Figure 74 ). Note:  Ensure that the spring ends are seated in the anchor grooves.
12. Install the belt covers ( Figure 75 ).
<PIC>
Figure 75


Question: How can you set up control of a over-the-range microwave?

CONTROL SET-UP
You can change the default values for beep sound clock, display speed and defrost weight. (LBS/KG) See following chart for more information.
<PIC>
Example: To change defrost weight mode from LbstoKg.
<PIC>


Question: How can you set the light timer of a over-the-range microwave?

 LIGHT TIMER

You can set the Lo Light to turn on and off automatically atanytime.The light will come on at the low setting the sametime everyday and turnoff at a set time until reset

Example: Turn on 2:00 AM, turn off 7:00 AM.

<PIC>
NOTE: ·To reset the time to turn on and off the Light, repeat steps1to5.

Example: To cancel the Light Timer
<PIC>
NOTE: If you want to cancel the Light Timer in operation touch Light HI/LO/Offthepad.


Question: How can you set yout favorite recipe with a over-the-range microwave?

FAVORITE RECIPE

Favorite Recipe lets you recall one cooking instruction previously placed in memory and begin cooking quickly

Example: To program cooking for 2 minutes
<PIC>

Example: To recall the custom recipe

<PIC>
·When the cook time is over, you will hear four beeps and ENDwill display.

NOTE:Power level will default to Hi,but this setting in modifiable.


Question: How can you reheat food with a over-the-range microwave?

REHEAT(SENSOR)

Reheat lets you heat foods without needing to program times and Power Levels. Reheat has preset Power Levels for 3 categories: Casserole,Dinner Plate and Soup/Sauce
<PIC>

Example: To reheat Casserole

<PIC>
When the cook time is over, you will hear four beeps and ENDwill display.

Recommended amounts:
<PIC>


Question: How can you use auto defrost of a over-the-range microwave?

AUTO DEFROST

Your microwave oven is preset with three defrost sequences.Using AUTO DEFROST is the best way to defrost frozen foods. The Auto Defrost Chart on pages 19-20 provides some basic guidelines for using the three defrost sequences.
<PIC>

Example: To defrost 1.2 Ibs. of ground beef.

<PIC>

NOTE: When you touch the START pad,the display changes to defrost time countdown.The oven will beep during the DEFROST cycle.Atthistime,open the door and turn, separate,or rearrange the food. Remove any portions that have thawed. Return frozen portions to the oven and touch START to resume the defrost cycle


Question: How can you clean the grease filter of a over-the-range microwave?

 CLEANING THE GREASE FILTER

The grease filter should be removed and cleaned often, at least once a month.

1.To remove grease filter,slide filter totheside.Pull filter downward and pushto the other side.Thefilter will dropout.

<PIC>

2.Wash in dishwasher or soak grease filter in hot water and a mild detergent.Rinse well and shake to dry.Do not use ammonia or place in a dishwasher.The aluminum filter will darken.

<PIC>

3. To reinstall the filter, slide it into the side slot, then push up and toward oven center to lock

<PIC>

 CAUTION

To avoid risk of personal injury or property damage,do not operate oven hood without filter inplace.


Question: How can you replace the charcoal filter of a over-the-range microwave?

CHARCOAL FILTER REPLACEMENT

If your oven is vented inside, the charcoal filter should be replaced every 6 to 12 months,and more often if nec essary.The charcoal filter cannot be cleaned.

1. Unplug the oven or turn off power at the main power supply.

 2. Remove the two vent grill mounting screws. (2 middle screws)

<PIC>

3. Tip the grill forward, then lift itout.

 4.Remove old filter.

<PIC>

5.Slidea new charcoal filter intoplace.The filter should rest at the angle shown.

<PIC>

6.Slide the bottom of the grill intoplace.Push the top until it snaps into place.Replace the mounting screws. Turn the power back on at the main power supply and set the clock.


Question: How can you replace the oven light of a over-the-range microwave?

OVEN LIGHT REPLACEMENT

1. Unplug oven or turn off power at the main power sup ply. 2. Remove the vent cover mounting screws. (2 middle screws) 3. Tip the cover forward, then lift out to remove.

<PIC>
4. Remove bulb holder

<PIC>

5. Lift up the bulb holder

<PIC>

6.Replace bulb with a 30 or 40 watt appliance bulb.

 7.Replace the bulb holder.

 8. Slide the bottom of the vent cover into place. Push the top until it snaps into place.Replacethe mounting screws.Turn the power back on at the main power supply or plugin the oven.


Question: How can you set the PCI Express 3.0 x16 slots of a motherboard?

1.5.4	 PCI Express  slots

This motherboard has three PCI Express  $3.0\,\mathsf{x}16$   slot that supports PCI Express 3.0 x16  graphic cards complying with the PCI Express specifications.
<PIC>

In single VGA card mode, use the PCIe   slot (gray) for a PCI Express x16  graphics card to get better performance. We recommend that you provide sufficient power when running some modes. See page 1-22 for details. Connect a chassis fan to the motherboard connector labeled CHA_FAN1/2/3 when  using multiple graphics cards for better thermal environment.

 IRQ assignments for this motherboard

<PIC>


Question: How can you set the jumpers of a motherboard?

1.6	 Jumpers
1.	 Clear RTC RAM (2-pin CLRTC)
This header allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can  clear the CMOS memory of date, time, and system setup parameters by erasing the  CMOS RTC RAM data. The onboard button cell battery powers the RAM data in  CMOS, which include system setup information such as system passwords.
<PIC>
Z170 PRO GAMING Clear RTC RAM
To erase the RTC RAM:
1.  Turn OFF the computer and unplug the power cord.
 2.  Use a metal object such as a screwdriver to short the two pins.
 3.  Plug the power cord and turn ON the computer.
 4.  Hold down the < Del > key during the boot process and enter BIOS setup to reenter data.
 If the steps above do not help, remove the onboard battery and short the two pins  again to clear the CMOS RTC RAM data. After clearing the CMOS, reinstall the  battery. You do not need to clear the RTC when the system hangs due to overclocking. For  system failure due to overclocking, use the CPU Parameter Recall (C.P.R.) feature.  Shut down and reboot the system, then the BIOS automatically resets parameter  settings to default values.
2.  CPU Over Voltage jumper (3-pin CPU_OV)
The CPU Over Voltage jumper allows you to set a higher CPU voltage for a flexible  overclocking system, depending on the type of the installed CPU. To gain more CPU  voltage setting, insert the jumper to pins 2-3. To go back to its default CPU voltage  setting, insert the jumper to pins 1-2.
<PIC>
Z170 PRO GAMING CPU_OV setting


Question: How can you set the rear panel connectors of a motherboard?

 1.7.1	 Rear panel connectors
<PIC>
1.	 PS/2 Mouse/Keyboard combo port.  This port connects to a PS/2 mouse or PS/2  keyboard.
 2.	 Display Port . This port is for a Display Port-compatible devices.
 3.  Video Graphics Adapter (VGA) port.  This 15-pin port is for a VGA monitor or other  VGA-compatible devices.
4.	 LAN (RJ-45) port.  This port allows Gigabit connection to a Local Area Network (LAN)  through a network hub.
<PIC>
LAN port LED indications
<PIC>
5.	 Center / Subwoofer port (orange) . This port connects the center/subwoofer speakers.
6.	 Rear Speaker Out port (black) . This port connects the rear speakers in a 4.1 channel,  5.1 channel, or 7.1 channel audio configuration.
7.	 Line In port (light blue).  This port connects to the tape, CD, DVD player, or other  audio sources.
8. 	 Line Out port (lime).  This port connects to a headphone or a speaker. In the 4.1, 5.1,  and 7.1 channel configurations, the function of this port becomes Front Speaker Out.
9.	 Microphone port (pink).  This port connects to a microphone.
Audio 2, 4.1, 5.1, or 7.1-channel configuration
<PIC>
10.	 Optical S/PDIF out port.  This port allows you to connect your PC to amplified  speakers, headphones, or Sony/Phillips Digital Interconnect Format (S/PDIF) compliant  devices.
11.	 USB 3.1 Type A port . This 9-pin Universal Serial Bus (USB) Type A port is for USB  3.1 devices.
12.	 USB 3.1 Type C port . This Universal Serial Bus (USB) Type C port is for USB 3.1  mobile or peripheral devices.
13.	 USB 3.0 ports 3\~6 . These 9-pin Universal Serial Bus (USB) ports are for USB 3.0  devices.
The plugged USB 3.0 device may run on xHCI or EHCI mode, depending on the  operating system’s setting.  USB 3.0 devices can only be used for data storage.We strongly recommend that you connect USB 3.0 devices to USB 3.0 ports for faster  and better performance from your USB 3.0 devices.  All USB devices connected to the  USB 2.0 and USB 3.0 ports are controlled by the xHCI controller. Some legacy USB  devices must update their firmware for better compatibility.  Multi-VGA output supports up to three displays under  environment, two  displays under BIOS, and one display under DOS.  Intel display architecture design supports the following maximum supported pixel  clocks (Pixel Clock  $=\mathsf{H}$   total  $\mathsf{x V}$   Total  $\mathsf{X}$   Frame Rate (Screen refresh rate)): -  Display Port port: 553 MHz -  DVI port: 165 MHz -  VGA port: 180 MHz   -  HDMI port: 300 MHz
14. 	 DVI-D port.  This port is for any DVI-D compatible device.
DVI-D can not be converted to output from RGB Signal to CRT and is not compatible with  DVI-I.
15.	 HDMI port.  This port is for a High-Definition Multimedia Interface (HDMI) connector,  and is HDCP compliant allowing playback of HD DVD, Blu-ray, and other protected  content.
16.	 USB 2.0 ports 13 and 14.  These two 4-pin Universal Serial Bus (USB) ports are for  USB 2.0/1.1 devices.


Question: How can you set the onboard LED of a motherboard?

 1.8	 Onboard LED

 1.	 Standby Power LED (SB_PWR)

The motherboard comes with a standby power LED that lights up to indicate that the  system is ON, in sleep mode, or in soft-off mode. This is a reminder that you should  shut down the system and unplug the power cable before removing or plugging in any  motherboard component. The illustration below shows the location of the onboard LED.

<PIC>
Z170 PRO GAMING Onboard LED

2.	 Model name LEDs

The model name LEDs are a group of five small LEDs, located right below the printed  model name. The LEDs light up in the following two modes to highlight the model  name.

<PIC>

Z170 PRO GAMING Model name LED Lighting

You can turn off the model name LEDs or change the lit modes from the BIOS or the LED  Control app in Ai Suite 3. To change the setting in BIOS, go to  Advanced  $>$    Onboard  Devices Configuration  $>$  Model Name LED Lighting  item. See section  2.6.7 Onboard  Devices Configuration  for details.
<PIC>

 3.	 SupremeFX LED

The SupremeFX LED lights up in the following three ways to bring you an ultimate  lighting effect. This LED also outlines the separation of the audio components from the  rest of your motherboard.

<PIC>
SupremeFX LED

Z170 PRO GAMING SupremeFX LED Lighting

You can turn off the SupremeFX LED or change the lit modes from the BIOS or the LED  Control app in Ai Suite 3. To change the setting in BIOS, go to  Advanced  $>$    Onboard  Devices Configuration  $>$    SupremeFX LED Lighting  item. See section  2.6.7 Onboard  Devices Configuration  for details.
<PIC>


Question: How can you update the BIOS file of a motherboard?

Updating the BIOS file

To update the BIOS file:

1.	 On the FreeDOS prompt, type  bupdater   and press  Enter.

2.	 On the BIOS Updater screen, press Tab to switch from Files panel to Drives panel  then select  D: .
<PIC>

3.	 Press Tab to switch from Drives panel to Files panel then press Up/Down or Home/ End keys to select the BIOS file and press <Enter>.

4.	 After the BIOS Updater checks the selected BIOS file, select  Yes  to confirm the BIOS  update.

<PIC>

The BIOS Backup feature is not supported due to security regulations.

5.	 Select  Yes  then press  Enter. When BIOS update is done, press  E S C   to exit BIOS  Updater.

6.	 Restart your computer.

DO NOT shut down or reset the system while updating the BIOS to prevent system boot  failaure.

Ensure to load the BIOS default settings to ensure system compatibility and stability. Select  the  Load Optimized Defaults  item under the  Exit  BIOS menu. See section  2.10 Exit  Menu  for details.


Question: How can you create RAID of a motherboard?

Creating RAID

To create RAID:

1.	 Press F11 on your keyboard or click   from the BIOS screen to open  EZ Tuning Wizard screen.

2.	 Click  RAID   then click  Yes  to enable RAID.

 Ensure that your HDDs have no existing RAID volumes. Ensure to connect your HDDs to Intel  SATA connectors.

3.	 The available HDDs display. Click  Next  to continue.

<PIC>

4.	 Select the type of storage for your RAID  Easy Backup  or  Super Speed , then click  Next .

<PIC>
a.	 For Easy Backup, select from  Easy Backup (RAID1)  or  Easy Backup (RAID10)  then click  Next .

<PIC>

You can only select Easy Backup (RAID 10) if you connect four (4) HDDs.

b.	 For Super Speed, select from  Super Speed (RAID0)  or  Super Speed (RAID5)  then click  Next .

<PIC>

5.	 After selecting the type of RAID, click  Yes  to continue the RAID setup.

6.	 After the RAID setup is done, click  Yes  to exit the setup then click  OK  to reset your  system.


Question: How can you use SATA ODD & USB devices to install an operating system for a motherboard?

Method 1: Using SATA ODD & USB devices

Load USB 3.0 drivers using the  support DVD and install  OS  7 using a USB  device.

Requirement:

The USB storage device requires 8 GB or more capacity. It is recommended to format the  storage device before use.

1.	 Insert the  OS 7 installation DVD into a USB ODD, or copy all files on the  OS  7 installation DVD to a USB storage device on a working system.

 2.	 Connect the USB ODD or USB storage device to your 100 series platform.

 3.	 Insert the  support DVD into a SATA ODD on your 100 series platform.

 4.	 Power on your system and press F8 during POST (Power-On Self Test) to enter the  boot screen.
<PIC>

6.	 The USB 3.0 driver will be loaded automatically during installation startup.

<PIC>

The “Setup is starting...” screen will show up if the USB 3.0 driver is loaded correctly.

 7.	 Follow the onscreen instructions to complete the OS 7 installation.


Question: How can you secure the motherboard to the  chassis?

Screw holes

Place nine screws into the holes indicated by circles to secure the motherboard to the  chassis.

Do not over tighten the screws! Doing so can damage the motherboard.
<PIC>
Place this side  towards the rear  of the chassis


Question: How can you prepare the installation of Central Processing Unit (CPU) for a motherboard?

Central Processing Unit (CPU)

This motherboard comes with a surface mount LGA1151 socket designed for 6th Generation processors.

<PIC>

Unplug all power cables before installing the CPU.

Ensure that you install the correct CPU designed for the LGA1151 socket only. DO  NOT install a CPU designed for LGA1150, LGA1155 and LGA1156 sockets on the  LGA1151 socket.
 Upon purchase of the motherboard, ensure that the PnP cap is on the socket and  the socket contacts are not bent. Contact your retailer immediately if the PnP cap  is missing, or if you see any damage to the PnP cap/socket contacts/motherboard  components.
Keep the cap after installing the motherboard. It will process Return Merchandise  Authorization (RMA) requests only if the motherboard comes with the cap on the  LGA1151 socket.
The product warranty does not cover damage to the socket contacts resulting from  incorrect CPU installation/removal, or mis placement/loss/incorrect removal of the PnP  cap.


Question: How do you know about system memory of a motherboard?

System memory

 Overview

This motherboard comes with four Double Data Rate 4 (DDR4) Dual Inline Memory Module  (DIMM) sockets. A DDR4 module is notched differently from a DDR, DDR2, or DDR3 module.  DO NOT install a DDR, DDR2, or DDR3 memory module to the DDR4 slot.

DIMM voltage below 1.65 V is recommended to protect the  CPU.

<PIC>
Z170 PRO GAMING 288-pin DDR4 DIMM sockets


Question: How do you know about Serial port connector (10-1 pin COM) of a motherboard?

Serial port connector (10-1 pin COM)

This connector is for a serial (COM) port. Connect the serial port module cable to this  connector, then install the module to a slot opening at the back of the system chassis.

<PIC>

Z170 PRO GAMING Serial port (COM) connector The COM module is purchased separately.


Question: How do you know about TPM connector (14-1 pin TPM) for a motherboard?

TPM connector (14-1 pin TPM)

This connector supports a Trusted Platform Module (TPM) system, which securely  store keys, digital certificates, passwords and data. A TPM system also helps enhance  the network security, protects digital identities, and ensures platform integrity.

<PIC>

Z170 PRO GAMING TPM connector


Question: How do you know about Thermal sensor connector (2-pin T_SENSOR)  of a motherboard?

Thermal sensor connector (2-pin T_SENSOR)

This connector is for the thermistor cable that allows you to monitor the temperature of  your motherboard’s critical components and connected devices.

<PIC>


Question: How can you install the  Mudguard of a rideon motorcycle?

1. Install the Mudguard.

As shown in step 1 , rotate the mudguard sideways then slide it up the left handle tube. Note! Do not allow the "convex point" to get caught in hole 1.
<PIC>
As shown in step 2, install the mudguard so the "convex point" enters hole 2
<PIC>


Question: How can you install  the Front Wheel of a rideon motorcycle?

3. lnstall the Front Wheel.

<PIC>

As shown in step 1, insert the front axle through the handle tubes and front wheel, with washers on either side of each handle tube.

Fasten the front axle and wheel to the handle tubes with two nuts, using the supplied spanners to tighten until the nuts reach the limit of the threads

<PIC>
NOTE
After assembling the front wheel and axle assembly, check the gap between the wheel and the handle tubes. If the gap is excessive and thewheel is notwell located, it is recommended to add additional washers (not supplied) between the wheel and the handle tubes. After doing this and reassembling the axle, check that the gap is minimal, however, that the wheel is able to spin freely. If the wheel is binding. remove a washer.


Question: How can you install the batteries for a bluetooth laser mouse?

 2. Installing the Batteries

The mouse needs two AA size batteries. Follow the steps below to install the batteries.
1. Press the button and the battery cover pops out.

<PIC>

2. Install two "AA" batteries while observing the polarity  indicated inside the mouse.

<PIC>

3. Replace the battery cover

<PIC>


Question: How can you install the WIDCOMM bluetooth stack  for a bluetooth laser mouse?

3.1 Installing the WIDCOMM Bluetooth Stack

Before installing the WIDCOMM Bluetooth stack, plug the USB Bluetooth dongle into a USB  port of your computer.  1. Insert the provided Installation CD in the CD ROM drive.   2. The installation stack loads automatically. If not, click the   Setup.exe  in the bin folder of the CD ROM.

3. The welcome screen introduces you to the installation process. Click  Next  to continue.

<PIC>

4. Read the agreement and select “ I accept he terms in the license agreement ”. Click  Next  to   continue.

<PIC>
5. The program will be installed in the folder as shown. Click  Change  to install in a different location.  Click  Next  to continue.

<PIC>

6. Click  Install  to start the installation. The installation may need some time to complete.

<PIC>

7. The following screen appears to indicate the installation is complete.

<PIC>
8. Remove the dongle and plug it back in, the mouse will pair automatically. Click  Finish  to exit   the installation.

The following prompt requires you to restart the computer so that the Bluetooth stack takes  effect. Click  Yes  to restart your computer now or  No  to restart later.

<PIC>


Question: How can you uninstall the WIDCOMM bluetooth stack for a bluetooth laser mouse?

3.2 Uninstalling the WIDCOMM Bluetooth Stack

Follow the steps below to uninstall the WIDCOMM Bluetooth stack from your computer.

1. Remove the USB Bluetooth dongle.

2. Click  Start   Settings  Control Panel  Add/Remove  Programs .

3. Select  WIDCOMM Bluetooth Software  from the program list and click  Remove

4. The system starts to remove the program, it may take some time to uninstall.

5. When the program has been removed, a prompt requires you to restart the computer. Click  Yes  to restart your computer now or  No  to restart later.


Question: How can you set quick pairing in Windows for a bluetooth laser mouse?

4.1 Quick Pairing in Windows

The Bluetooth mouse has been set to a pre-pairing mode as the factory default. For quick pairing, enable the

pre-pairing mode following the steps below.

1. Plug the USB Bluetooth dongle into a USB port of your computer.

2. For the mouse, press the pairing button at its bottom.

Pairing button

<PIC>
3. Press the button on the bottom of the USB Bluetooth dongle until the LED begins to flash   once every second. This indicates the. Bluetooth dongle has started to search for device to  be paired.(   This mouse will be sold without dongle. )

<PIC>

4. Move your mouse to ensure they are connected.

Enabling the function of USB mouse in BIOS

If the mouse failed to work (refer to  “7 Troubleshooting”  on page 14 for more probable  conditions), check that the USB function of the mouse has been enabled in the BIOS setup.   Some old PC systems do not support the USB keyboard/mouse in   BIOS/DOS environment.


Question: How can you set pairing on WIDCOMM bluetooth stack for a bluetooth laser mouse?

4.2 Pairing on WIDCOMM Bluetooth Stack

Before using the Bluetooth stack for mouse pairing, install the stack as instructed in  $\mathbf{\ddot{3}}$   Installing  and Uninstalling the WIDCOMM Bluetooth Stack”  . Then follow the steps below.

1. Press the USB Bluetooth dongle button until the following Human Interface Device (HID) screen  appears.

<PIC>
2. When the mouse is connected, the following confirmation message appears. Click to confirm  that the correct mouse is connected.

<PIC>


Question: How can you check power status of a bluetooth laser mouse?

5.1 Power Status of the Laser Mouse

The Bluetooth mouse has a battery status LED. When the battery runs out,   the LED turns amber. You should change the batteries immediately  .(The top LED indicate is the same with bottom LED)

<PIC>

To view more detailed information on the mouse battery status, go to the  Control panel     Mouse  Bluetooth .

<PIC>


Question: How can you use the stack for the first time for a bluetooth laser mouse?

6.1 Using the Stack for the First Time

To start using the Bluetooth Stack, double click the Bluetooth icon in the system tray.

<PIC>

1. The  Initial Bluetooth Configuration Wizard  will launch. Follow the instructions on screen to

   complete the configuration.

2. When the Bluetooth Configuration is complete, the following HID screen appears and starts to  search for Bluetooth devices.

<PIC>

3. Click on the HID device you want to connect with. Then follow the instructions on-screen to   enable the selected device.

About the Bluetooth icon

The Bluetooth icon acts as an indicator for dongle status.

1. A red icon indicates there is no dongle inserted.

 2. A white icon indicates the dongle is plugged in.

 3. A green icon indicates the dongle has detected the HID devices.


Question: How can you connect a bluetooth laser mouse to the other HID devices?

6.2 Connecting to the other HID Devices

Besides the mouse, the Bluetooth Stack also allows you to connect to other Bluetooth devices.

1. Make sure the USB Bluetooth dongle has been plugged onto your computer.

 2. Set the Bluetooth devices, such as printers, modems, and PDAs, you want to connect to the  Bluetooth stack.

 3. Press the USB Bluetooth dongle button until the following HID   screen appears.

 4. Select the type of devices to search for from the drop-down menu.

<PIC>

5. The detected devices will be displayed. Click on a device and the stack will instruct you to enable   the connection.


Question: How  can you remove the door of a oven?

To remove the door:

1. Open the door fully.
2. Lift the catches and push them forwards as far as they will go (fig. 1).
<PIC>

3. Close the door as far as it will go (A), lift it up (B) and turn it (C) until it is released (D) (fig. 2).
<PIC>


Question: How  can you refit the door of a oven?

To refit the door:

1. Insert the hinges in their seats. 2. Open the door fully. 3. Lower the two catches. 4. Close the door.


Question: How  can you move the top heating element (some models only) of a oven?

 MOVING THE TOP HEATING ELEMENT (SOME MODELS ONLY)

1. Remove the side accessory holder grilles (Fig. 3).
<PIC>

2. Pull the heating element out a little (Fig. 4)
<PIC>
 and lower it (Fig. 5).
<PIC>

3. To reposition the heating element, lift it up, pulling it slightly towards you, be sure it comes to rest on the lateral supports.


Question: How  can you  replace the rear lamp (if present) of a oven?

 To replace the rear lamp  (if present):

1. Disconnect the oven from the power supply.

 2. Unscrew the lamp cover (Fig. 6),
<PIC>

replace the lamp (see note for lamp type) and screw the lamp cover back on (Fig. 7).
<PIC>

 3. Reconnect the oven to the power supply.


Question: How  can you use a drip-tray of a oven?

Drip-tray (Fig. 1)
For collecting fat and bits of food when placed under the wire shelf, or as a plate for cooking meat, chicken and fish, etc., with or without vegetables. Pour a little water  into the drip-tray to avoid spatters of fat and smoke.
<PIC>


Question: How can you clean the oven exterior?

Oven exterior

IMPORTANT: do not use corrosive or abrasive detergents. If any of these products unintentionally comes into contact with the appliance, clean  immediately with a damp cloth.

Clean the surfaces with a damp cloth. If it is very dirty, add a few drops of washing up detergent to the water. Finish off with a dry cloth.


Question: How  can you use a wire shelf of a oven?

Wire shelf (Fig. 3)
For grilling food or as a support for pots, cake tins and other cooking receptacle. It can be placed on any available level. Thewire shelf can be inserted with its curvature  facing up or down.
<PIC>


Question: What can you do with catalytic side panels of a oven?

Catalytic side panels (Fig. 4)
These panels have a special micro porous enamel coating that absorbs fat spatters. It is advisable to do an automatic cleaning cycle after cooking particularly fatty food  (see CLEANING).
<PIC>


Question: How  can you use baking tray of a oven?

Baking tray (Fig. 2) For baking biscuits, cakes and pizzas.
<PIC>


Question: How  can you use grill pan set of a oven?

Grill Pan Set (Fig. 6) The set comprises a wire shelf (6a) and an enamelled recipient (6b). This set must be placed on the wire shelf (3) and used with the Grill function.
<PIC>


Question: How  can you use grease filter of a oven?

Grease filter (Fig. 7) Use  only  for particularly greasy cooking. Hook it on the rear wall of the oven compartment, opposite the fan. It can be cleaned in a dishwasher and used with the fan  assisted function.
<PIC>


Question: How  can you use sliding shelves of a oven?

Sliding shelves (Fig. 8)
They allow the wire shelves and drip-trays to be pulled half out during cooking. Suitable for all the accessories, they can be cleaned in a dishwasher.
<PIC>


Question: How can you attach the shoulder strap to a hybrid instant camera?

Attaching the Shoulder Strap  (Purchased Separately)
Attach the strap clips to the camera, then attach the  shoulder strap.

Open a strap clip. Use the clip attaching tool to open a strap clip as  shown.
<PIC>
Keep the tool in a safe place. You will need it to  open the strap clips when removing the shoulder  strap.

Place the shoulder strap clip on each  strap eyelet.
Hook the strap eyelet in the clip opening. Remove the  tool using the other hand to keep the clip in place.
<PIC>

 Pass the clip through each strap eyelet.
Rotate the clip fully through the eyelet until it clicks closed.
<PIC>

Pass the shoulder strap through each clip.
<PIC>


Question: How can you insert the battery for a hybrid instant camera?

 Inserting the Battery

<PIC>
Slide the battery cover to open.

<PIC>
Insert the battery according to the arrow on it.  Make sure the yellow line on the battery aligns with  the mark on the camera. To remove the  battery, press the battery latch to  the side, and slide the battery out of the camera.

<PIC>
Close the battery cover.


Question: How can you load thefFilm pack for a hybrid instant camera?

 Loading the Film Pack

<PIC>
Press and hold the button of the film door lock ( 1 ),  then slide the lever to the right until the film  door opens slightly.

<PIC>
Hold both sides of the  film pack, align the  bottom of the film pack  on the groove of the film  chamber, then insert  it straight ( 2 ).

<PIC>
Close the back cover.  Make sure the back cover  lock clicks into place.

<PIC>
The film cover (black) is  ejected automatically when  the back cover is closed.  Remove the film cover from  the film ejection slot.


Question: How can you unload a used film pack for a hybrid instant camera?

 Unloading a Used Film Pack

When no film is left, all dots on the right of the shooting  screen are displayed in gray. (Page 52)  Unload the film pack.

<PIC>
Press and hold the button of the film door lock ( 1 ),  then slide the lever to the right  $(\boxdot$   until the film  door opens slightly.

<PIC>
Grasp the rectangular  holes on the film pack,  then pull it out straight.


Question: How can you set auto print mode of a hybrid instant camera?

Auto Print Mode

Switch the print mode selector on the side to "AUTO".
<PIC>

The icon below appears on the shooting screen.
<PIC>

Printing starts immediately after the image is saved in the  memory.
<PIC>


Question: How can you set manual print mode (initial setting) of a hybrid instant camera?

Manual Print Mode (initial setting)

Switch the print mode selector on the side to “MANUAL”.
<PIC>

The icon below appears on the shooting screen.
<PIC>

The image is saved in the memory. You can select and print  images later instead of printing them immediately.
<PIC>


Question: How can you take a picture with a hybrid instant camera?

Taking a Picture

This section describes basic operation for photography.

Turn the lens ring (power switch) clockwise to turn  the camera on.
<PIC>

Hold the camera and confirm the desired  composition of the final image.
<PIC>

Select the shooting mode or perform the steps to  select your image effects. (Pages 53 to 57)

Press the shutter button halfway to focus.

 If the camera is able to focus: The camera beeps and the green focus frame  appears on the monitor.

 If the camera is unable to focus: The red focus frame appears on the monitor.  Change the composition or use focus lock. (Page  55)

Lightly press the shutter button the rest of the way  down to take the picture.
The picture is taken and it is saved in the camera’s  memory. If the print mode is set to auto print mode, the  image will be printed. (Page 49)

When you take a picture, hold the camera with both  hands and brace your elbows against your sides.

 Be careful not to touch the lens surface when you  press the shutter button.

 When you press the shutter button fully, press it  lightly.

Be careful that your fingers or the strap do not cover  the flash, lens, or film ejection slot.

 If a subject is poorly lit, the flash may fire when the  picture is taken. You can change the flash setting to  disable flashing. (Page 56)

Cautions on the camera’s memory
When the memory becomes full, the shutter will not  release and you cannot take a picture. Delete the  images in the memory or use another memory card.

 You can save up to 50 images in the memory. 1000  images per 1 gygabyte can be saved if you use a  memory card.

 Images in the memory may be damaged or lost if the  camera has any trouble. We recommend you store  important image files as backup using other media  (e.g. Hard disk, CD-R, CD-RW, or DVD-R, etc.).

 If you ask for repair, we do not guarantee the safety of  images in the memory.

 While the camera is being repaired, note that we may  check the contents of images in the memory.


Question: How can you  insert the memory card for a hybrid instant camera?

Inserting the Memory Card

Slide the card slot cover to open.
<PIC>

As shown below, slide in the memory card until it  clicks into place at the back of the slot.
<PIC>

Close the card slot.
<PIC>
$\circledast$    To remove the memory card, press it in and release it  slowly. The card can be removed by hand.


Question: How can you  use the flash with a hybrid instant camera?

Using the Flash

Use the flash when shooting at night or indoors under low light.

Press the MENU/OK button on the shooting  screen.
<PIC>
The shooting menu appears.

Select  FLASH , then press the  MENU/OK button.

Select the flash setting, then press the MENU/OK  button. See the right column for details on each flash  setting.

Press the shutter button to shoot.


Question: How can you  use the self timer with a hybrid instant camera?

Using the Self Timer

Use the self timer to include a photographer in a group  photo or to reduce blur when the shutter button is pressed.

Press the MENU/OK button on the shooting  screen.

<PIC>
The shooting menu appears.

Select  SELF-TIMER , then press the  MENU/OK  button.

Select  10 SEC  or  2 SEC , then press the MENU/OK  button.

Press the shutter button fully.
 When you select  10 SEC : When you press the shutter button, the AF-assist  illuminator/Self timer lamp lights up, and then it  flashes 3 seconds before shooting. When you select  2 SEC : When you press the shutter button, the AF-assist  illuminator/Self timer lamp flashes.

 To cancel the self timer, press the  (Back) button.


Question: What do you  know about Film remaining indication of a hybrid instant camera?

Film remaining indication

Dots on the right of the monitor indicates the number  of remaining films. One dot turns gray every time you print an image.
<PIC>
When there are only two films left, dots turns  red.

 You can print an image that is zoomed in or print four  or nine images on one film. Use the command dial to  change to the multiple image display on step 2 when  the image to print is displayed. (Page 51)

For details on taking out the film, refer to the instructions and  warnings on the Instant Film “instax SQUARE” pack. The development time is approximately 90 seconds. (The  time varies depending on the ambient temperature.)
You can select an effect menu directly by pressing a button on the rear to adjust the image effect while the shooting/ playback screen is displayed.


Question: How can you  use the command dial with a hybrid instant camera?

Using the command dial
<PIC>
Use the command dial on the following  occasions. Selecting a menu or item Changing playback display (Page 51)  Adjusting the value of image effect  (Pages 53 and 54)


Question: How can you  charge from a PC for a hybrid instant camera?

Charging from a PC:
Connect the camera and PC directly. Do not connect  them via a keyboard or USB hub.
If the PC enters the sleep mode while charging is in  progress, charging will stop. If you continue charging,  resume the PC and reconnect the USB cable.
You may not be able to charge the camera from a PC  depending on your PC specifications, settings, or status.


Question: How can you set quick release for a multi-use pressure cooker and air fryer?

Quick Release (QR or QPR)
Stops cooking quickly and prevents overcooking. Perfect for quick-cooking vegetables and delicate seafood!

What to do
Press the quick release button down until it clicks and locks into the Vent position.
<PIC>

What to expect
When pressed down, a jet of steam ejects through the top of the steam release valve.
This is normal!
When pressure has been fully released, the float valve drops into the lid.
<PIC>


Question: How can you set pressure cooking lid for a multi-use pressure cooker and air fryer?

Pressure cooking lid
<PIC>

Removing the lid
01 Grip the lid handle and turn it counterclockwise to align the symbol on the lid with the symbol on the rim of the cooker base.
02 Lift the lid up and off the cooker base towards your body
<PIC>

Closing the lid
01 Align the symbol on the lid with the symbol on the cooker base, then lower the lid onto the track.
02 Turn the lid clockwise until the symbol  on the lid aligns with the symbol on the cooker base.
<PIC>


Question: How can you set float valve for a multi-use pressure cooker and air fryer?

Float Valve
The float valve is a visual indication of whether there is pressure in the cooker (pressurized)or not(de pressurized). It appears in 2 positions:

Pressurized
The float valve has visibly popped up above the surface of the lid.
<PIC>

De pressurized
The float valve has descended, and the top is flush with the lid.
<PIC>

The float valve and silicone cap work together to seal in pressurized steam. These parts must be installed before use. Do not attempt to operate the Multi-use pressure cooker and air fryer without the float valve properly installed. Do not touch the float valve during use.

DANGER
DO NOT attempt to remove the lid while the float valve is up and NEVER attempt to force the lid open.Contents are under extreme pressure.Float valve must be downbefore attempting toremove the lid.Failure to follow these instructions may result in serious personal injury and/or property damage


Question: What do you know about anti-block shield for a multi-use pressure cooker and air fryer?

Anti-block shield
The anti-block shield prevents food particles from coming up through the steam release pipe, assisting with pressure regulation.
The anti-block shield is integral toproduct safety and necessary for pressure cooking.
<PIC>


Question: How can you set steam release valve for a multi-use pressure cooker and air fryer?

Steam release valve

Remove the steam release valve

Pull the steam release valve up and off the steam release pipe.
The steam release valve must be installed before using the cooker.
<PIC>

Install the steam release valve

Place the steam release valve on the steam release pipe and press down firmly

The steam release valves its loosely on the steam release pipe when installed properly but should remain in place when the lid is turned over.

<PIC>


Question: How can you set anti-block shield for a multi-use pressure cooker and air fryer?

Anti-block shield

Remove the anti-block shield

Grip the lid like a steering wheel and use your thumbs to press firmly against the side of the anti-block shield (pressing towards the side of the lid and up) until it pops off the prongs underneath.
<PIC>

Install the anti-block shield

Place the anti-block shield over the prongs and press down until it snaps into position
Donot attemptto operate the pressure cooker withoutthe anti-block shield installed.
<PIC>


Question: How can you set silicone cap and float valve for a multi-use pressure cooker and air fryer?

 Float valve and silicone cap

 Remove the float valve from the lid

Place one finger on the flat top of float valve,thenturn thelidover.Detachthe silicone cap from the bottom side of the floatvalve.

Remove the float valve from the top of the lid. Do not discard the float valve or silicone cap.
<PIC>

 Install the floatvalve

Drop the narrow end of the floatvalve into the float valve hole on the top of the lid. Place one finger on the flat top of the float valve,thenturn thelid over.Firmly attach the silicone cap to the bottom of the floatvalve.

Do not attempt to operate the pressure cooker without the float valve and/or silicone cap properly installed in the pressure cooking lid
<PIC>
Bottom


Question: How can you Install the condensation collector for a multi-use pressure cooker and air fryer?

 Install the condensation collector

Align the grooves on the condensation collector over the tabs on the back of the cooker base and slide the condensation collector into place.
<PIC>


Question: How can you install the sealing ring for a multi-use pressure cooker and air fryer?

 Install the sealing ring

Place the sealing ring over the sealing ring rack and press itinto place.Press down firmly to prevent puckering.
When installed properly, the sealing ring is snug behind sealing ring rack and should not fall out when the lid is turned over.
<PIC>


Question: How can you remove silicone sealing ring for a multi-use pressure cooker and air fryer?

Remove the sealing ring

Grip the edge of the silicone and pull the sealing ring out from behind the circular stainless-steel sealing ring rack.

With the sealing ring removed, inspect the steel rack to make sure it is secured centered, and an even height all the way around the lid. Do not attemptto repair a deformed sealing ring rack.

 The sealing ring is easiest to remove and install when it is wet and soapy.
<PIC>


Question: What do you know about sealing ring of a multi-use pressure cooker and air fryer?

Sealing ring
When the pressure cooking lid is closed. the sealing ring creates an air-tight seal between thelid and the inner pot.
The sealing ring must be installed before using the cooker. Only one sealing ring should be installed in the lid at a time
Tip:Silicone is porous, so it absorbs strong aromas and certain flavors. Keep extra sealing rings on hand to limit the transfer of aromas and flavors between dishes.
<PIC>


Question: What do you know about  steam release valve of a multi-use pressure cooker and air fryer?

Steam release valve

The steam release valve sits loosely on the steam release pipe. When the cooker releases pressure, steam ejects from the top of the steam release valve
The steam release valve is integral to product safety and necessary for pressure cooking.
<PIC>

A WARNING
Do not cover or block the steam release valve in any way.


Question: What do you know about quick release button of a multi-use pressure cooker and air fryer?

Quick release button
The quick release button controls the steam release valve - the part controls whether pressure is released or not.
<PIC>

What we love about it
It's really easy to use, andkeeps our hands far away from the steam!

What you should know about it
The lid says Turn toSeal, but it's more like a flicking motion. Don't turn the quick release button more than  $\%^{\prime\prime}$  (or  $45^{\circ},$  ,and let it spring back to its original position.
See Releasing pressure:Venting methods for safe de pressurization techniques


Question: What can you know about natural release(NRorNPR) of a multi-use pressure cooker and air fryer?

Natural Release(NRorNPR)

Cooking stops gradually. As the temperature within the cooker drops, the cooker de pressurizes naturally over time.
<PIC>

NOTICE
Use NR to de pressurize the cooker after cooking high-starch foods (e.g., soups, stews, chilis, pasta, oatmeal and congee) or after cooking foods that expand when cooked (e.g., beans and grains).


Question: What are the proper steps to safely stop the engine of a pump?

 Stopping the engine

1.Move the throttle lever fully to left
<PIC>

2.Turn the engine switch to the"OFF”position

$\textcircled{1}$  “OFF"
<PIC>

3.Turn the fuel cock lever to the“OFF"position

$\textcircled{1}$  “OFF"
<PIC>


Question: What are the key components of a water pump?

LOCATION OF IMPORTANT LABELS

<PIC>

Please read the following labels carefully before operating this machine.

TIP

Maintain or replace safety and instruction labels,as necessary.

# DESCRIPTION

$\textcircled{\scriptsize{1}}$  Fuel tank

  $\circleddash$  Fuel tank cap

  $\circledast$  Fuel cock

  $\textcircled{4}$  Air filter cover

  $\circledast$   Spark plug

  $\circledcirc$  Muffler

  $\textcircled{\scriptsize{2}}$  Choke lever

  $\circledast$  Engine switch

  $\circledcirc$  Oil filler cap

  $\circledcirc$   Oil drain plug

  $\circledcirc$  Recoil starter

  $\circledcirc$  Oil warning light

  $\textcircled{3}$  Throttle lever

  $\textcircled{4}$   Priming plug

  $\textcircled{5}$  Water drain plug


Question: What is the detailed procedure for cleaning the fuel tank filter?

Fuel tank filter

1.Remove the fuel tank cap and filter

  $\textcircled{1}$  Fuel tankcap

  $\circleddash$  Fuel tank filter

 2.Clean the filter with solvent If damaged, replace.

 3.Wipe the filter and insert it.

<PIC>


Question: What is the correct procedure for safely draining the fuel out of a pump?

Drain the fuel

1. Drain the fuel tank, fuel cock, and carburetor float bowl.

$\circledast$  Carburetor drain plug

2.Pour acupofSAE 10W30or 20 W 40 motor oil into the tank.

 3.Shake the tank to coat the inner surfaces thorOughly.

 4.Drain off the excess oil.

 <PIC>


Question: What are the potential causes when a water pump fails to draw up water, and how can these issues be effectively diagnosed and resolved?

Water does not draw up

o Loosened priming and/or drain plugs .... Tighten o Loosened hose joint and/or band .... Tighten. oDamaged O-ring and/or gaskets... Replace o Damaged mechanical seal ... Consult dealer


Question: What is the robot anatomy of the vacuum?

TOPVIEW
<PIC>

BUTTONS&INDICATORS
<PIC>

BOTTOMVIEW
<PIC>


Question: What are the two primary modes available on a vacuum cleaner that can be used to tailor its performance to meet different home cleaning needs?

Halo Mode: When the switch is in the "down" position, the device crea fes a protective zone fh a fRoom ba wil not enter.This prevents vacuum from bumping into itemsyou want to protect (e.g. a dog bowl or vase) or crossing into undesired areas(e.g.a corner or under a desk).the halo is invisible and reaches ap proxima f ely 24 inches from the center of the device.(SeeFigure3)

<PIC>

Virtual Wall Mode: When the switch is in the "up" position, the device functions as a virtual wall.This means that you cansef if fo block openings of up fo 1ofeet. If crea fes an invisible,cone-shaped barrier th af only vacuum can see.(SeeFigure2)

<PIC>


Question: What is the proper procedure for emptying the vacuum cleaner's bin?

 EMPTYING THE BIN

1. Press bin release button to remove bin. (See Figure 4)

<PIC>

2. Open bin door to empty bin. (See Figure 5)

<PIC>

NOTE: If the full bin indicator comeson at any time during a cleaning job, you can always pause the cleaning job to empty the bin and then continue cleaning. If the full bin indicator is illuminated, but the bin does not appear to be full, refer to Cleaning the Full Bin Sensors.


Question: What is the correct procedure for cleaning the vacuum cleaner filter?

 CLEANING THE FILTER

3.Remove filter by grasping the yellow tab. (See Figure 6)

<PIC>

4. Shake off debris by tapping the filter against youi trash container. (See Figure 7)

<PIC>

IMPORTANT!The filter door won't close unless a filter is reinserted. Insert the filter with theyellow tab facing up.


Question: What is the proper procedure for cleaning the full bin sensors on a vacuum cleaner?

 CLEANING THE FULL BIN SENSORS

1. Removeand empty the bin. (See Figure 8)

<PIC>

2. Wipe the sensors withaclean,dry cloth. (See Figure 9)

<PIC>

3. Wipe the inner and outer sensol ports on the bin withaclean,dry cloth. (SeeFigure 10)

<PIC>


Question: What is the correct procedure for cleaning the extractors (brushes or rollers) on a vacuum cleaner?

 CLEANING THE EXTRACTORS

1. Pinch the yellow extractor frame release tabs, lift up the extractor frame and remove any obstructions. (SeeFigure 15)

<PIC>

2. Remove the extractors and remove the yellow extractor caps. Remove any hair or debris that has collected underneath the caps and around the metal axles. Reinstall the extractor caps. (See Figure 16)

<PIC>

3. Remove hair and debris from the square and hexagonal plastic pegsonthe other side of the extractors. (See Figure 17)

<PIC>

4. Clear the vacuum path. (See Figure 18)

<PIC>

5. Reinstall the extractors. Match the color and shape of the extractor pegs with the color and shape of the extractor icons on the cleaning head module


Question: What is the proper procedure for cleaning the sensors and charging contacts on a vacuum cleaner?

 CLEANING THE SENSOR AND CHARGING CONTACTS

1. Wipe the sensor with a clean,dry cloth. Do not spray cleaning solution directly on to the sensors or sensor openings. (See Figure 13)

<PIC>

2. Wipe the charging contacts on Room ba and the Home Base with a clean,drycloth.(See Figure 14)

<PIC>


Question: What is the correct procedure for positioning the home base of a vacuum cleaner?

 POSITIONING THE vacuum

Place the vacuume in an open, uncluttered area, leaving the following distances around the unit

Atleast1.5 feet on each side of the vacuum Afl east 4 fee fin front of the vacuum,andafleast 4 feet away from stairs. ·Atleast 8 feet from virtual wall barriers.

Always keep the vacuum plugged in and make sure it is in an area with consistent coverage to allow vacuum to receive information via the app


Question: What is the proper procedure for cleaning the front caster wheel of a vacuum cleaner?

 CLEANING THE FRONT CASTER WHEEL

1. Pull firmly on the frontwheel to remove it. (See Figure 11)

<PIC>

2. Remove any debris frominside the wheel cavity.

3. Spin the wheel by hand. If rotation is restricted,remove thewheel from its housing and push firmly to remove the axle and clear any debris or hair wrapped around it.

4. Reinstall all parts when finished.Make sure the wheel clicks back into place.


Question: What is the correct procedure for cleaning the side brush of a vacuum cleaner?

 CLEANING THE SIDE BRUSH

1. Use a coin or small screwdriver to remove the screw. (See Figure 12)

<PIC>

2. Remove the brush clean the brush and the brush post, and reinstall the brush.


Question: What is the function of the dual-mode virtual wall barrier on a vacuum cleaner?

 THE DUAL MODE VIRTUAL WALL BARRIER

The dual mode virtual wall barrier keeps vacuum inthe places you want fo becleaned-andout of the onesyou don't. In between cleaning cycles, you canleave the device operating in its nn s it in nan the

floor.You can sef your device fo one off wo modes f of it yourhome's cleaning needs.(SeeFigure 1)

NOTE: Under normal use, batteries will last 8-10 months. If you are not planning on using your virtual wall devicefor an extended period of time and you would like to store it, be sure to switch it to the "Off "(middle) position.

<PIC>


Question: What are the troubleshooting steps if the vacuum indicates a problem?

 TROUBLEHSOOTING

vacuum will tell you something is wrong with a two-tone distress sound followed by a spoken message.The troubleshooting indicator will also blink.More detailed support and videos are available through the app and online.

# RE BOOTING INSTRUCTIONS

For some errors,rebooting vacuum may resolve the problem.To reboot vacuum,press and hold CLEAN for 10 seconds until all indicators illuminate,then release. Whenyou release the CLEAN button,youwill hearan audible f one signifying a successful reboot.

NOTE: If you use vacuum's scheduling feature open the app after rebooting fo confirm that schedule remains intact.

# REDUCED POWER STANDBY MODE

Vacuum consumes a small amount of power anytime to ensure that it is ready for its next cleaning job as well as fo main fain Wi-Fi connectivity.It is possible fo put vacuum in a further-reduced power statewhen not inuse. For instructions and more details on this reduced power standby mode,refer to the app.

# LITHIUM ION BATTERY

For best results,only use the lithium ion battery that comes with vacuum.While vacuum will operate witholder-model batteries,its performance will be limited.

IMPORTANT!Lithium ion batteries and products that contain lithium ion batteries are subject to stringent transportation regulations. If you need to ship this product (with the battery included) forservice, travel or any other reason,you Must comply with the following shipping in sfr ucf ions:

·Remove the lithium ion battery from the product. Place a piece of tape over the battery's metal charging contacts ·Reinstall thebattery (with the tapeon it) in the product and secure the ba ffe ry door. ·Package the product in its original packaging or in your own packaging that prevents any movement during transportation. Ship via ground transportation only (no air shipping)


Question: What are the detailed instructions for T-rail mounting of a camera or equipment?

 T-rail Mounting Instructions

To mount your camera on a drop ceiling T-rail, use the included hardware. The hardware can be used to mount to most 9/ 16"，15/16",or11/2"T-rails.

1. Using the dashed lines on the mount plate template as a guide, set the proper spacing of the clips.
<PIC>

2. Tighten the set screws on the  $\mathsf{T}$  -rail clips and secure them using a  $5/64^{\circ}$   $(2\,\mathsf{m m})$  hexkey.

<PIC>

3. Attach the mount plate to the  $\mathsf{T}$  -rail clips using the mount plate holes (marked with a  $"G"$  》
<PIC>

4. Attach the T-rail clips to the T-rail by rotating them and snapping them into place as shown. The black foam pads should be compressed slightly after installation.

<PIC>
Standard6-32x4mm T-railscrews
<PIC>
Modifications for recessed T-rail


Question: What are the steps to power the camera?

 Powering the camera

Remove the cable guard and route the Ethernet cable from an active port on a 802.3af PoE switch or PoE injector

Note:Power over Ethernet supports a maximum cable length of 300 ft(100m)


Question: What is the proper way to use the brake lever and brake button?

 BRAKE LEVER                                                                                The machine is stopped by braking the entire drive system Squeeze the brakel ever towards the handlebar to stop the machine.

$\textcircled{1}$  Brakelever

  $\circledcirc$  Brakel ever end

  $\textcircled{3}$  Handlebar end

NOTE: When the brake is operated,thebrake light will illuminate

<PIC>

Besure the brakel ever end does not project out over the handlebar end. This will help prevent brake lever damagewhen the machine is placed onits side for service.

<PIC>

When parking the machine or starting the engine, apply the parking brake. Squeeze the brakel ever  $\textcircled{1}$  ,then push down  $\textcircled{3}$  theparking brake button  $\circledcirc$  while releasing the brake lever. To release the parking brake,just squeeze the brakel ever.

Always set the parking brake before attempting to startthe engine. Never run the machine with the parking brake ap? plied. This may overheat thebrake disc and reduce brak ing ability.


Question: What are the essential preparation checks to perform before using a snowmobile?

  PRE-OPERATION CHECKS

Pre-operation checks should be made each time the machine is used.

# WARNING

Theengine and muffler will be very hotafter the engine has been run.

Avoid touching the engine and muffler while they are still hot with any part of your body or clothing during inspection or repair.

<PIC>

# FUEL

Make sure there is sufficient fuel in both main and sub tanks.

Recommended fuel: Unleaded gasoline Pumpoctane  $\textstyle{\frac{\mathsf{R}+\mathsf{M}}{2}}$  ; 88 or higher Fuel tank capacity:  $\textcircled{1}$  Main tank: 15 L (3.3 Imp gal, 4.0 US gal)  $\circledcirc$  Sub tank: 9.3 L (2.05 Imp gal, 2.46 US gal)
<PIC>

# WARNING

·Fuel is highly flammable and poisonous.Check "SAFETY INFORMATION"(seepage3-2)carefully before refueling.

 ·Do not fill the fuel tank all the way to the top. When the machine is tilted,this could cause the fuel to overflow. Make sure that thefuel tank cap is closed securely after refueling.Leaking fuel can catch fire.

 <PIC>

# CAUTION:

Oxygenated fuels(gasohol")containing max.  $5\%$  of ethanol can be used, although richer jetting may berequired to prevent engine damage.Consult a  dealer.Gasohol containing methanol is not recommended.
·Besure that snow and/or ice does not enter into the fuel tankwhen refueling.

<PIC>


Question: What are the detailed steps to start the engine of a snowmobile?

STARTING THE ENGINE

# WARNING

Be sure to check"SAFETY INFORMATION"care- fully before starting the engine. Be sure the parking brake is applied

NOTE: Be sure the engine stop switch is inthe“ON"position

1. Fully open the starter lever (choke)

$\textcircled{1}$  Starter lever(choke)

  $\circledcirc$  Fully open (cold engine starting)

  $\textcircled{3}$  Half-open (warm engine up) (CS340E/ET410TR/VK540E)

  $\textcircled{4}$  Close (warm engine starting)

# NOTE:

The starter lever(choke)is not required when the engine iswarm.Put the starter lever in the“Close”position

Manual Starting Model

2.Turn the main switch to the“ON"position

$\textcircled{1}$  "ON"

Pull slowly on the recoil starter until it is engaged,then o ull it briskly.After the engine starts,warmupthe engine until it does not run roughly or begin to stall when the starter lever is returned tothe“Close"position.
<PIC>

Pullslowly on therecoil starter until it is engaged,then pullit briskly.After the engine starts,put the starter lever (choke)inthe"Half-open”position.Warm up the engine until it does not run roughly or begin to stall when the starter lever is returned to the“Close"position.

Electric Starting Model

<PIC>

2.Turn the main switch to the“START”position After the engine starts,put the starter lever (choke) in the “Half-open" position. Warm up the engine until it does not run roughly or begin to stall when the starter lever is returned to the“Close”position.

$\textcircled{1}$  “START"

#  CAUTION:

Release the switch immediately after the engine starts.

If the engine fails to start,release the switch,wait a fewseconds,then tryagain.Each attempt should be as short aspossible topreserve thebattery. Do not crank the engine more than 10 seconds on anyone attempt.


Question: What is a V-BeltHolder?

V-BELTHOLDER
Keep a spare V-belt for emergency use by putting itinto the holder provided.

NOTE: Loosen the bolt  $\textcircled{1}$  to remove the V-belt

<PIC>

# CAUTION:

·Besure to tighten the bolt when installing theV-belt in the holder.

<PIC>


Question: What are the steps to adjust the throttle cable on a snowmobile?

THROTTLE CABLE ADJUSTMENT

# CAUTION:

Be sure the engine idle speed is adjusted first

1.Loosen the adjuster lock nut.

 2.Turn the adjuster in or out until proper throttle lever free play is achieved.

<PIC>

$\circledcirc$  Locknut

  $\textcircled{3}$  Adjuster

3. Tighten the locknut

<PIC>


Question: What is the proper way to use the steering system on a snowmobile?

STEERING SYSTEM

1.Check the following for excessive free play: 1）Push the handlebar up and down and back and forth. 2）Turn the handlebar slightly to the right andleft

 2. If excessive free play is noticed, consult a  dealer.

LIGHTSCheck the lights. Replace any burned out bulbs

<PIC>


Question: What are the correct steps to turn using a snowmobile?

TURNING

For most snow surfaces, “body English" is the key to turning.

As you approach a curve,slowdown and begin to turn the handlebars in the desired direction. As you do so,put your weight on the running board to the inside of the turn and lean your upperbody into the turn.

This procedure should be practiced at slow speed many times in a large flat area with no obstacles.Once you have learned this technique,you should be able to perform it at higher speeds or in tighter curves.Lean more as the turn gets sharper or is made at higher speeds
Improper riding procedures such as abrupt throttle changes excessive braking,incorrect body movements,ortoomuch speed for the sharpness of the turn may cause the snowmobile to tip.

If your snowmobile begins to tip while turning, lean more into the turn to regain balance.If necessary,gradually let off on the throttle and/orsteer to the outside of theturn.

<PIC>


Question: What are the proper techniques for riding uphill on a snowmobile?

<PIC>

# RIDING UPHILL

You should practice first on gentle slopes.Try more difficult climbs only after you have developed your skill.Asyou approacha hill, accelerate before you start the climb, and then reduce the throttle opening to prevent track slippage. It is also important tokeep your weight on the uphill side at alltimes.On climbs straight upthehill this canbeaccomplished byleaning forward and,on steeper inclines, standin gon the running boards and leaning forward over the handlebars.(AIsosee“CROSSING A SLOPE.")


Question: What are the proper techniques for riding downhill on a snowmobile?

RIDING DOWNHILL

When riding downhill,keep speed to a minimum.It is important to apply just enough throttle to keep the clutch engaged while descending the hill.This will allow you to use engine compression to help slow the machine, and to keep the snowmobile from rolling freely down the hill.Also apply the brake frequently,withlight pressure.

<PIC>


Question: What are the correct techniques for crossing a slope on a snowmobile?

CROSSING A SLOPE (SIDE HILL)

# WARNING

Side hills are not recommended for a beginner or novice snowmobile r.

Crossing thefaceofa slope(sidehill)requires you to properly position your weight to maintain proper balance. As you travel across the slope,lean your body to position your weight towards the up hillside.A recommended riding position is to kneel with the knee of the downhill leg on the seat and the foot of the uphill leg on the running board.This position will make it easier for you to shift your body weight asneeded.

Snowand ice are slippery,so be prepared for the pos sibi lit y that your snow-mobile could begin to slip sideways on theslope.If this happens,steerin the direction of theslide if there areno obstacles in your path.As you regain proper balance,gradually steer again in the direction you wish to travel.

If your snowmobile starts to tip,steer down the hill toregain balance.

<PIC>


Question: What are the steps to inspect the spark plug on a snowmobile?

The spark plug is an important engine component and is easy to inspect.The condition of the spark plug can indicate something of the condition of the engine.Check the coloration on the white porcelain insulator around the center electrode.The ideal coloration at this point is a medium to a light tan color for a machine that is being ridden normally.If as park plug shows a distinctly different color,there could be something wrong with the engine.For example,a very white center electrode porcelain color could indicate an in take track air leak or car bure tion problem for that cylinder.Do not attempt to diagnose such problems yourself.Instead，take the machine to your  dealer.You should periodically remove and inspec t the spark plug because heat and deposits will cause any spark plug to slowly breakdown and erode.Consult your dealer before changing to a different type of spark plug.

Spark plugs are produced in several different thread lengths. The thread length (reach) is the distance from the spark plug gaskets eat to the end of the threaded portion. If thereach is toolong,overheating and engine damage mayresult. If the reach is too short, spark plug fouling and poor performance mayresult.Also,if tooshort,carbonwill form on the exposed threads resulting in combustion chamber hot spots and thread damage.Alwaysusea spark plug with the proper reach.

<PIC>


Question: What are the steps to clean a snowmobile?

1. Cleaning

Thoroughly clean the machine,inside andout，to remove the corrosive salts and acids that can accumulate.Use Mud and Grease Release,oran equivalent,to loosen mud,greaseand grime. Wash with mild soap, then rinse and dry completely.


Question: What are the best methods for memorizing communication channels using a manual program?

 Memorizing the Channels by MANUAL PROGRAM

Using the MEMORY/ERASE button

You can conveniently perform MANUAL PROGRAM using the MEMoRY/ERASE button on the remote control.

 1.Pressthe  $\pmb{\triangle}/\pmb{\nabla}$  or NUMBER buttons to select the channel number you want to memorize or erase.

 2.Press the MEMORY/ERASE button to select Memory or Erase. Theon screen display appears asshown right.

<PIC>

# Using the MENU

1. Press the MENU button and then  $\pmb{\triangle}/\pmb{\nabla}$  button the until the menu is displayed as shown right.

 2.Press the  $\blacktriangleright$  and thenuse  $\pmb{\triangle}/\pmb{\nabla}$  button to select Manual

 3.Pressthe  $\blacktriangleright$  button and then use  $\pmb{\triangle}/\pmb{\nabla}$  button to select Channel.

 4.Press thebutton and then use  $\pmb{\triangle}/\pmb{\nabla}$  button to select the channel numberyou want to memorize or erase.

 5. Press the  button and then use  $\pmb{\triangle}/\pmb{\nabla}$  button to select Memory.

 6. Press the  $\blacktriangleright$  button and then  $\pmb{\triangle}/\pmb{\nabla}$  to select On or off

 7. Repeatedly press the MENUbutton to exit.

 <PIC>


Question: What are the common causes and conditions that can lead to poor reception in television or radio signals?

IIGNITION:

Picture may flutter, drift, suffer from black spots or horizontal streaking.Usually caused by interference from automobile ignition systems，neonlamps,electrical drills and other electrical appliances.

<PIC>

# GHOSTS:

Ghosts are caused when the TV signal splits and follows two paths. One is the direct path and the other is reflected off tall buildings, hills or other objects. Changing the direction or position of the antenna may improve reception.

<PIC>

# SNOW:

If your receiver is located at the weak, fringe area of a TV signal your picture maybe marred by small dots.It maybe necessary to install a special antenna to improve the picture.

<PIC>

[2 An old, bad or illegally recorded tape is played.

 [3 Strong, random signals from a car or airplane interfere with the TV signal.

 [4 The signal from the antenna is weak.

 [5The program wasn't captioned when it was produced, transmitted or taped
# Using the Text Function

Text services give a wide variety of information on all kind of subjects (ex. captioned program lists, weather forecasts, stock exchange topics, news for hearing-impaired---) through the full TV screen. But not all stations offer text services, even though they might offer captioning.

Note: In the event you receive a poor signal, an empty black box may appear and disappear,even when the text mode is selected This is normal function in such an event.


Question: What are the steps to enable and customize captions and on-screen text settings on a television?

Operating the Caption and Text

Using the CAPTION button

1.Press the CAPTIoN button

 2.Press the CAPT lON button to select OFF,Mode1,Mode2,Text1 OrText2.

 3.Press the ENTER(O)button to exit

 <PIC>


Question: What are the steps to properly connect and set up an outdoor antenna for optimal signal reception?

 Connecting an Outdoor Antenna

For the best reception, we recommend you use an outdoor antenna Severely weathered antennas and antenna cables can reduce the signal quality.Before connecting it, necessarily inspect them.Any service center canexplain thevarious outdoor antennas available toyou

# 300 Ohm Flat Wire

1. Connect the 300 ohm flat wire to screws on the 300 ohm to 75 ohm adapter.

 2. Push the end of 300 ohm to 75 ohm adaptel into 75 ohm antenna jack.

75 Ohm Coaxial Cable 1. Connect the 75 ohm coaxial cable directly to the 75 ohm antenna jack

<PIC>

# Connecting a CATV Cable

If you subscribe to a CATV system, change the antenna connection as described below.

1. Remove the 300 to 75 ohm adapter or the cable from the set if attached.

 2. Connect the CATV cable (75 ohm coaxial cable) to the 75 ohm antenna jack

 <PIC>


Question: What are the steps to properly connect a DVD player to a television or audio system for optimal performance?

·Connect component DVD inputs to Y, PB, PR(480i) and audio IN to audio(L/R) ports

 ·Note: This TV is programmed to remember which mode it was last set to, even if you turn the TV off

# 1.How to connect

<PIC>


Question: What are the key factors to check when troubleshooting technical issues or malfunctions?

Troubleshooting check list

# SYMPTOMS

<PIC>


Question: What safety precautions should be followed to ensure safe operation during this process?

Cleaning

Unplug this television receiver from thewall outlet before cleaning.Do not useliquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Do not use attachments not recommended by the television receiver manufacturer as they may cause hazards.

# Power Supply

This television receiver should be operated only from the type of power source indicated on the marking label.lf you are not sure of the type of power supplied to your home,consult your television dealer or local power company.

# Installation

Do not use this television receiver near water, for example,near a bathtub,washbowl,kitchen sink or laundry tub,in a wet basement,or near a swim mingpool,etc.

Do not place this television receiver on an unstable cart,stand，ortable.The television receiver may fall,causing serious injury to a child or an adult, and serious damage to the appliance. Use only with a cart or stand recommended by the manufacturer,or sold with the television receiver. Wall or shelf mounting should follow the manufacturer's instructions and should use a mounting kit approved by the manufacturer.

Slots and openings in the cabinet and the back or bottom are provided for ventilation, and to insure reliable operation of the television receiver,andto protect it from overheating. These openings must not be blocked or covered. The openings should

# Writing Model And Serial Numbers

The serial number and model number are found on the back of this unit.The serial number is unique to this unit. You should record requested information here and retain this guide as a permanent record of your purchase.Please retain your purchase receipt as your proof of purchase.

never be blocked by placing the television receiver ona bed,sofa,rug,or other similar surface.This television receiver should not be placed in a builtin installation such as a bookcase unless proper ventilation is provided

It is recommended not to operate this unit near speakers or big metallic furnitures in order to keep their magnetism from disturbing colors purity (uniformity) on thescreen.

# Wet Location Marking:

Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids,such asvases, shall beplaced on the apparatus.

# Use

Donot allow anything to reston the power cord. Do not locate this television receiver where the cord will be abused by persons walking on it. Do not overload wall outlets and extension cords as this can result in fire or electric shock. Never push objects of any kind into this television receiver through cabinets lots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Neverspill liquidof anykind on the television

receiver.

# Service

Do not attempt toservice this television yourselt as opening or removing covers may expose you to dangerous voltage or other hazards.Referall servicing to qualified personnel.


Question: What are the steps to set the date and time on a thermostat for accurate scheduling and temperature control?

 19 Set date and time

19 Set the date. Press  $^+$  or - to adjust the year. Press Select. Press  $^+$  or - to adjust the month Press Select. Press  $^+$  or -to adjust the day. Press Select.

<PIC>

# 20 Choose a clock format.

Press+or-set the clock format 12hour(standard for North America)or24hour.Press Select

<PIC>

21 Set the time.

Press  $^+$  or - to adjust the hour. Press Select.

Press  $^+$  or-to adjust the minutes Press Select.

<PIC>


Question: What are the steps to adjust the system and fan operation settings on a thermostat to optimize heating and cooling performance?

 System operation settings

1 Press the Mode button to cycle to the next available System mode.

2 Cycle through the modes until the required System mode is displayed and leave it to activate.

NOTE:Available System modes vary by model and system settings.

<PIC>

System modes: - Auto: Thermostat selects heating or cooling as needed. -Heat:Thermostat controls only the heating system. -Cool:Thermostat controls only the cooling system -Em Heat(only for heat pumps with auxiliary heat): Thermostat controls Auxiliary Heat. Compressor is not used. -Off: Heating and cooling system is off. Fan will still operate if fan is set to On or Circulate.

NOTE: Heat/Cool flash for 5 minutes due to compressor protection

# Fan operation settings

1 Press the Fan button to cycle to the next available Fan mode. 2 Cycle through the modes until the required Fan mode is displayed and leaveitto activate.

NOTE:Available Fan modes varywith system settings.

<PIC>

Fan modes:

-Auto:Fan runs only when the heating or cooling system is on. -On: Fan is always on. -Circ:Fan circulates randomly about  $33\%$  of the time.


Question: What are the steps to adjust the program schedules on a thermostat for efficient energy usage and temperature control?

 Program Schedule

You can program four time periods each day, with different settings for weekdays and weekends.Were commend the pre-set settings(shown in the table below), since they can reduce your heating/cooling expenses.

Wake-Setto the time you wake up and the temperature you want during the morning,until you leave for the day.

Away-Set to the time you leave home and the temperature you want while you are away(usuallyan energy-saving level).

Home-Set to the time you return home and the temperature you want during theevening,until bedtime.

Sleep - Set to the time you go to bed and the temperature you want overnight (usually an energysaving level).

<PIC>
The above table is only an example

NOTE: To temporarily or permanently override any of the above program schedules,seepage 12

# To adjust program schedules

1 Press Menu on your thermostat

<PIC>

2 PROG is displayed.Press Select.Then ON is displayed.Press Select 3 Press  $^+$  or-to select day or set of daystoedit.Press Select. 4 Press  $^+$  or-to selecta schedule period to edit (Wake, Away, Home, and Sleep).Press Select. 5 ON is displayed.Press Select to keep the schedule period on.Orpress  $^+$  and then Select to turnoff the schedule period. 6 Time starts blinking.Press  $^+$  or-to adjust the schedule period start time.Press Select. 7 Temperature starts blinking. Press + or-to adjust the “Heat"setpoint temperature.Press Select.Press  $^+$  or-to adjustthe“Cool"temperature setpoint.Press Select.

<PIC>

 8 Repeat steps 4 through 7 for the remaining schedule periods. 9 Press Home when you're finished to save program settings and return to the home screen.

 <PIC>


Question: What are the steps to change the temperature setting on a thermostat temporarily without affecting the programmed schedule?

 Program schedule override (temporary)

1Press  $^+$  or- to adjust the temperature

Once atthe desired setpoint temperature,no further action is needed. The new setpoint temperature will beheld until the next scheduled time period begins For more information on schedule time periods, see"Program Schedule onpage11.

<PIC>

3 To cancel the Temporary Hold, Press  $^+$  or-and then press Cancel

# Program schedule override(permanent)

1Press  $^+$  or - to adjust the temperature

2 TEMPORARY HOLD is displayed and the set point temperature flashes While it's flashing, press Hold (Mode) button to change to Permanent Hold

3 To cancel the Permanent Hold, press  $^+$  or-and then press Cancel

<PIC>


Question: What actions should you take when an alert screen appears on your device or system?

 Alerts screen

1 You will see the alert icon  on the home screen. You can access alerts in the Menu to view the error/alert code. Once viewed the home screen will maintain the alert symbol until it is cleared.

<PIC>

2 Snoozed alerts will appear 7 days after dismissing themin the alerts menuscreen.

<PIC>

3 When the alert icon appears, check the error code with the table below to determine the problem.

<PIC>

4 Snooze the alert.

<PIC>

5 Dismiss the alert.

<PIC>

# Alerts codes

<PIC>


Question: What are the steps to modify the wiring for heat pumps specifically, ensuring proper connection and functionality?

 Alternate wiring (for heat pumps only)

# NOTES:

1. Keep R Slider Tab in the up position (1 wire). 2.If your old thermostat had both Van dVR wires,stop now and contact a qualified contractor for help. 3. If your old thermostat had separate O and B wires, attach the B wire to the C terminal.If another wire is attached to the C terminal,stop now and contact a qualified contractor forhelp 4.If your old thermostat had Y1,w1 and w2 wires, stop now and contact a qualified contractor for help.

<PIC>


Question: What are the steps to safely replace the battery in a thermostat, ensuring proper functionality after installation?

 Battery replacement

Batteries are required to provide power.Install fresh batteries immediately when the low battery icon appears. The icon appears about two months before the batteries are depleted.

Even if the low battery icon does not appear, you should replace batteries once a year, or before leaving home for more than a month.

If batteries are inserted within two minutes, the time and day will not have to be reset. All other settings are permanently stored in memory, and do not require battery power.

<PIC>

NOTE: When replacing batteries, alkaline batteries are recommended.